Showing results: 61 - 75 of 77 items found.
-
STT-CSS-20P1 -
Beijing KeHuan Century EMC Technology Co,.LTD
*Using 2 The regulator, and the rated voltage adjustable automatic voltage regulator, power fluctuations avoid adversely affecting the test results. Simulate the test under 110V power supply. It can simulate the fluctuation of the power grid under extreme conditions (such as high or low power supply voltage in remote areas).
-
RP4030 -
Teledyne LeCroy
The Teledyne LeCroy RP4030 Power Rail Probe meets the specific requirements of those who need to acquire a low-voltage DC signal as part of a:-Comprehensive power integrity, digital power management IC (PMIC), voltage regulator module (VMR), point-of-load (POL) switching regulator, or low-dropout regulator testing- Complete embedded power management system that includes PMICs, VRMs, POLs, and LDOsThe RP4030 will faithfully acquire a low-impedance, low-voltage DC power/voltage rail signal without unduly loading the device under test (DUT), while providing high offset to allow DC power/voltage rail signal display on an oscilloscope with high gain.
-
ViTec Co. Ltd
The measuring system consists of a test site and a control rack. The test site is equipped with a mounting for the test tool with measuring sensors: vibration, torque and speed, as well as a pneumatic regulator, a filter and a powder type brake clutch. The maximum torque test is performed until the rotation is completely stopped. The screen displays both the directly measured maximum torque and the calculated maximum power of this sample. At the end of the test, the results are presented to the operator on the monitor screen.
-
3270 Series （350V,1875W~22500W） -
PRODIGIT Electronics Co, Ltd.
3270 Series is suitable for the step, square and sine wave of the AC Power device test, especially for the uninterruptible power supply UPS, Inverter, fuses, circuit breakers, power regulator AVR, battery, AC / DC power supply / components ... and so on, absolutely is the best test solution in the market.
-
SERIES S400 TYPE RX I O/ I OACP -
K&S Engineering and Scientific Ltd
The output is continuously variable from zero to 10 kV by means of the panel mounted regulator. An output trip is fitted which operates when the output exceeds 25 mA switches off the test set and operates a neon overload indicator. Primary protection is provided by two panel mounted fuses. The output is protected by the output trip and a magnetic/hydraulic circuit breaker.
-
RX30/4P -
K&S Engineering and Scientific Ltd
The output is continuously variable from zero to 10 kV by means of the panel mounted regulator. An output trip is fitted which operates when the output exceeds 25 mA switches off the test set and operates a neon overload indicator. Primary protection is provided by two panel mounted fuses. The output is protected by the output trip and a magnetic/hydraulic circuit breaker.
-
ELAK Private Ltd.
ELAK Auto Electrical Test Bench is a table model and has been designed to cater to the needs of Auto Electricians, Garages, Services Centers, Transport Corporations, Educational Institutions and other bulk users of Auto Electrical Equipments, for complete testing of Alternator, Regulator and their associated parts. It also has a built-in D.C. Power Supply to check Free-run of Starter Motors.
-
Reltech Limited
Reltech Limited holds over 35 years’ experience in the design and manufacture of all types of qualification test hardware. Our advanced technology products include: HTOL Boards (Mother and Daughter cards) Burn-In Boards HAST Boards THB (humidity) Boards Burn-In Modules and frames Dynamic Driver cards (Digital, Analogue and Mixed signal) Back Planes Voltage regulator cards Custom electro-mechanical assemblies DUT Cassettes and test Fixtures
-
MBT300 -
Matco Tools
Tests 6/12/24V lead acid batteries individually or in parallel and series battery packs. Displays battery or battery pack condition as % available capacity, rated capacity (CCAs), state of charge voltage, and good or replace status. Tests 6/12/24/36V starter and charging systems including starter draw, alternator and regulator output (loaded/unloaded), and diode ripple.
-
Mostrak-2 -
ipTest Limited
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
-
MS012 COM -
MSG Equipment
The device simulates installation of voltage regulator on faultless alternator in order to test its operating performance under different loads and modes, under various rotor resistance parameters. The handset tester conducts diagnostics of all existing types and models of voltage regulators.New types and models of voltage regulators can easily be added by updating software through USB-port. The equipmentis controlledby three encoders and a sensor on colored display. Diagnostics lasts about 2 minutes.
-
Eco Bump -
Teledyne Gas & Flame Detection
Importantly, bump testing is the only way to validate that gas detectors will respond to gas and trigger user alarms.Simplified configuration (no software).Measuring only 7.2” (180mm) in height (including the push button regulator), the pocket-sized EcoBump can easily be stored and transported with minimal shipping costs.With 5.5L of bump gas capacity, EcoBump provides approx. 250 bump tests from a single cylinder making it our most cost effective bump solution.
-
TestVonics, Inc.
TestVonics offers oil-less compressors offer outstanding performance and value for those who demand the most quiet, dependable clean air systems. All units come equipped with a tank, pressure regulator with built-in moisture trap and line pressure gauge, tank pressure gauge, safety valve, air intake filter and motor cooling fan. Compressors also feature a built in desiccant dryer, providing clean, dry air for the ADC-2500 Series or other test equipment.
-
ForTest Italia Srl
T8730 was designed for the precise task of measuring flows on parts such as filters (medicinal, diesel or petrol), tubes, nozzles, openings, valves, etc…Other than the classic flow measurement, the tool also has other ways of making it as versatile as possible in its category: ascent and descent ramps, opening tests and burst testing.Another separate function is the "continuous measurement", i.e. a test with infinite times allowing adjustment of the taps and part repairs in real time.The tool also avails of an intelligent pressure adjustment, which uses the automatic pressure regulator to continuously adjust the test pressure based on the variation in load loss, to ensure the reading is as stable and repetitive as possible.
-
SFJ018 -
Shanghai Launch Electric Co., Ltd.
SFJ018 relay protection test cabinet uses double carbon brushes regulator, big buttons for regulating AC/DC voltage, current under large loading, small buttons for regulating AC/DC voltage, current under small loading,. The two output channels could work simultaneously. It also take use of digital meters of Grade 0.5, sensor of high accuracy, six digital display stop watch, satisfying requirements for time measurement.
